Does Rubbing Alcohol Kill Mold? 70% vs 99%, Contact Time, 6 Surfaces

Illustration: a leather armchair arm with faint mildew spots and a folded white cloth

The short answer

The answer to does rubbing alcohol kill mold is partly: a 2020 lab study reports 70% alcohol killed all tested Penicillium spores after 5 minutes wet, but CDC says alcohol evaporates too fast for long contact, and a 2015 test found 70% ethanol did not stop two indoor molds growing. According to CDC, 60% to 90% strength works best, so 70% beats 99%. On hard surfaces, scrub and dry instead.

Is 70%, 91% or 99% isopropyl alcohol better for killing mold?

70%, and the reason is the water in the bottle. CDC's disinfection and sterilization guideline says the most likely way alcohol kills microbes is by denaturing their proteins, and that absolute alcohol is less effective than alcohol mixed with water because proteins denature faster when water is present. The same guideline reports the optimum as 60% to 90% alcohol in water, by volume, and says activity drops sharply below 50%.

Per the CDC range, a 70% bottle sits near the middle, 91% sits 1 point past the top, and 99% is nearly water free. CDC describes alcohols as fungicidal, but its kill figures are for bacteria and viruses in clinical use, and its fungal figures are for ethyl alcohol, not the isopropyl sold as rubbing alcohol.

Bottle strength Water in the bottle Versus CDC 60% to 90% optimum Flash point, per source
70% isopropyl About 30% Inside 53.6 to 69.08°F (Greenfield 70% SDS)
91% isopropyl About 9% 1 point above the 90% upper bound No 91% SDS opened for this page
99% isopropyl About 1% Above; CDC: alcohol without water denatures protein more slowly 53°F for pure isopropanol (NIOSH)
Water share is 100 minus the label strength. Optimum range and the water mechanism, data from CDC's disinfection and sterilization guideline; flash points from Greenfield Global's 70% isopropyl SDS and the NIOSH Pocket Guide entry for isopropyl alcohol. Retrieved 12 November 2026.
Where each mix sits on CDC’s alcohol strength scaleWHERE EACH MIX SITS ON CDC’S ALCOHOL STRENGTH SCALECDC optimum 60 to 90Activity drops sharply below 50 (CDC)0%25%50%75%100%70% rubbing alcohol91%99%30%: ACRYLITE acrylic limit35%: 1 to 1 mix of 70% and water
Strength bands, data from CDC's disinfection and sterilization guideline: cidal activity drops sharply below 50% and the optimum is 60% to 90% in water, by volume. Per the maker, 30% is the dilution ACRYLITE's cleaning instructions accepts on acrylic sheet; the 35% mark is nominal arithmetic for the 1 cup to 1 cup recipe in UF/IFAS Extension's mildew removal sheet. Retrieved 12 November 2026.

Does rubbing alcohol kill mold spores, or only the fuzz you can see?

The best evidence is mixed, and none of it uses isopropanol. According to Rogawansamy and colleagues, 2015, published in the International Journal of Environmental Research and Public Health, 70% ethanol was tested by disc diffusion against Aspergillus fumigatus and Penicillium chrysogenum isolated from indoor air. The study reports it had no visible effect on the growth of either fungus, and the authors concluded 70% ethanol is not suggested as an effective antifungal treatment. Vinegar inhibited only the Penicillium.

A food plant study points the other way when contact lasts. Visconti and colleagues, 2020, in the International Journal of Food Microbiology, volume 332, exposed Penicillium commune spores to 70% ethanol and reports that 5 minutes inactivated all of them, more than 4 log10, across every strain and growth condition tested. At 1 minute, dry harvested spores grown at water activity 0.950 still had survivors, and at 2 minutes one strain still did. The most resistant strain differed from the other three by 2.35 log10 at 1 minute.

Minutes of wet contact 70% ethanol needed against fungiMINUTES OF WET CONTACT 70% ETHANOL NEEDED AGAINST FUNGI0 min5 min10 min15 min20 minUnder 1 min: tissue phaseof 4 fungi killed (CDC)1 min: survivors in onespore type (Visconti 2020)2 min: survivors inone strain only5 min: all spores killed,over 4 log10 (Visconti 2020)About 20 min: culture phaseon surfaces (CDC)
Ethanol data, not isopropyl: 1, 2 and 5 minute results are Penicillium commune conidia from Visconti and colleagues, 2020; the under 1 minute and about 20 minute figures are the tissue and culture phases of dimorphic fungi reported in CDC's disinfection and sterilization guideline. Separately, Rogawansamy and colleagues, 2015 reports 70% ethanol did not inhibit Aspergillus fumigatus or Penicillium chrysogenum growth on agar. Retrieved 12 November 2026.

CDC's disinfection and sterilization guideline reports two clinical data points for ethyl alcohol at 70%: the tissue phase of four fungi died in under 1 minute, while the culture phase on contaminated surfaces needed about 20 minutes. The spread from 1 to 20 minutes is the practical lesson: every result above assumes the surface stays wet, which a single wipe of a fast evaporating liquid does not guarantee.

Illustration: a varnished wooden dresser top with a mildew bloom near an open window
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

Can a rubbing alcohol wipe stay wet for the 5 minutes spores needed?

Rarely, because it evaporates fast. CDC's disinfection and sterilization guideline says alcohols evaporate rapidly, making extended exposure difficult to achieve unless the item is immersed. The NIOSH Pocket Guide entry for isopropyl alcohol lists a vapor pressure of 33 mmHg and a boiling point of 181°F for pure isopropanol, and lists it as a Class IB flammable liquid, a volatile solvent rather than a product built to sit on a surface.

Two practical consequences follow. On a small, hard item such as a plastic toothbrush cup or a stainless sink rim, soaking or rewetting the surface is the only way to approach the 5 minute figure from Visconti and colleagues, 2020. On a wall or ceiling, no realistic number of passes keeps it wet that long, which is one reason chapter 3 of EPA's mold remediation guide relies on physical removal: it says mold can generally be removed from nonporous surfaces by wiping or scrubbing with water and detergent, and that the surface should then be dried quickly and thoroughly.

No bottle of rubbing alcohol is a registered mold killer by default. Under 40 CFR 152.15, a product sold with a claim that it destroys a pest must be registered with EPA, so the label, not the chemistry, decides whether a mold claim exists. A product that does make the claim prints an EPA Reg. No. and a dwell time; compare those on our mold killer page.

What does rubbing alcohol do to leather, wood, vinyl, acrylic, drywall and fabric?

Alcohol earns its place on the surfaces where water is the bigger risk, such as leather and finished furniture, and loses it on porous building materials. The table pairs each surface with the published maker or extension instruction, which usually calls for diluted alcohol after a gentler step, never a full strength soak.

Surface What alcohol does Published instruction Source
Smooth, finished leather Can lift dye that is not colorfast and pulls oil out of the hide Test colorfastness, wipe with 1 cup denatured alcohol to 1 cup water, dry in moving air; then mild soap or saddle soap if mildew remains UF/IFAS; UGA adds a conditioner afterwards to return oil and prevent cracking
Finished wood furniture Softens shellac; CDC records alcohol damaging shellac mountings Vacuum, then a cloth with mild detergent wrung almost dry; diluted alcohol, 1 cup to 1 cup water, only if mold remains UF/IFAS; Alabama Extension
Vinyl and rubber (floor tile, gaskets) CDC: bleaches rubber and plastic tiles; swells and hardens rubber after repeated use Warm sudsy water, rinse, wipe dry CDC guideline; UGA chart for vinyl and linoleum floors
Acrylic sheet (shower panels, display cases) Undiluted alcohol can cause fine surface cracks called crazing Isopropyl diluted to 30% is accepted; alcohol is on the do not use list ACRYLITE maker instructions
Painted drywall Wets the paint film only; mold on the back face is untouched Porous materials may have to be thrown away; above 10 sq ft use EPA’s larger job guide EPA home cleanup page; EPA chapter 3, Photo 3B
Fabric and upholstery Damages acetate, triacetate, modacrylic and acrylic fibers Vacuum and sun dry first; then sponge with 1 cup alcohol to 1 cup water and dry; on acetate, dilute with 2 parts water UGA; UF/IFAS
Surface guidance from UF/IFAS Extension's mildew removal sheet, UGA Extension's mold and mildew stain chart, Alabama Cooperative Extension, ACRYLITE's cleaning instructions, CDC's disinfection and sterilization guideline, EPA's Mold Cleanup in Your Home page and chapter 3 of EPA's mold remediation guide. Retrieved 12 November 2026. Spot test any surface first.

Leather is the clearest case for alcohol. UF/IFAS Extension's mildew removal sheet lists a 1 cup to 1 cup wipe as the first step for mildewed leather goods, and UGA Extension's mold and mildew stain chart follows any alcohol step with a leather conditioner. The full leather cleanup, including suede, is on our mold on leather page.

Painted drywall is the clearest case against it. chapter 3 of EPA's mold remediation guide shows wallboard whose front looks fine while the back is covered with mold, and EPA's Mold Cleanup in Your Home page says porous materials such as ceiling tiles and carpet may have to be thrown away if they become moldy. A wipe of rubbing alcohol on the paint reaches neither side of that problem. Wood tables, dressers and upholstered pieces are handled step by step on our mold on furniture page.

How much water turns 70% or 91% rubbing alcohol into the 30% acrylic mix or the 1 to 1 leather mix?

The extension recipes and the maker limit use different strengths, and none of them match the bottle. The table below does the arithmetic: final strength equals bottle strength times alcohol volume divided by total volume. A 1 cup to 1 cup mix of a 70% bottle lands at 35%, under the 50% line where, according to CDC's disinfection and sterilization guideline, killing activity drops sharply.

Starting bottle 1 cup to 1 cup water gives For 30% (ACRYLITE acrylic) For 50% (CDC lower edge)
70% bottle 35% 1.33 parts water to 1 0.4 parts water to 1
91% bottle 45.5% 2.03 parts water to 1 0.82 parts water to 1
99% bottle 49.5% 2.3 parts water to 1 0.98 parts water to 1
Labelled calculation, nominal volume arithmetic on label strengths, not a measured concentration. Limits from ACRYLITE's cleaning instructions and CDC's disinfection and sterilization guideline; the 1 to 1 recipe from UF/IFAS Extension's mildew removal sheet. Retrieved 12 November 2026.

That makes the 1 to 1 recipes cleaning solutions, not disinfectant strength, which matches how UF/IFAS Extension's mildew removal sheet uses them: as a wipe to lift mildew from leather and upholstery, followed by drying. For a 70% bottle on acrylic, 3 cups of alcohol to 4 cups of water gives the 30% that ACRYLITE's cleaning instructions accepts, per the arithmetic above.

Illustration: an acrylic shower panel and tile grout with small black mold dots
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

Is a 53°F flash point a problem when you wipe mold in a closed bathroom?

It can be. According to the NIOSH Pocket Guide entry for isopropyl alcohol, pure isopropanol has a flash point of 53°F, a lower explosive limit of 2.0% in air, an upper limit of 12.7%, and classes it as a Class IB flammable liquid, defined there as a flash point below 73°F. Diluting to 70% does not lift it above 73°F, per the SDS figures below.

Greenfield Global's 70% isopropyl SDS, revision dated 28 June 2024, reports a flash point of 53.6 to 69.08°F, classes the 70% product as a Category 2 flammable liquid, and warns that vapors may travel a considerable distance to an ignition source and flash back. an EDM3 70% isopropyl SDS, issued 21 May 2024, reports a 12°C closed cup flash point. Both sheets say to keep the liquid away from sparks and open flames.

In a bathroom or utility room that means no candles, no gas water heater pilot nearby, and an exhaust fan or open window, which EPA's biocide page asks for with any disinfectant: always ventilate the area and exhaust the air to the outdoors. The NIOSH Pocket Guide entry for isopropyl alcohol also lists chlorine and acids among isopropanol’s incompatibilities, so never mix rubbing alcohol with bleach or vinegar in the same bottle.

When should you scrub with detergent instead of reaching for rubbing alcohol?

On most household mold, by EPA’s own rule. EPA's biocide page, last updated 8 September 2026, says dead mold may still cause allergic reactions, so it is not enough to kill it: it must be removed. EPA's Brief Guide to mold gives the method, scrub mold off hard surfaces with detergent and water and dry completely, and sets a 24 to 48 hour window to dry wet materials before mold grows.

Size is the second test. EPA's Mold Cleanup in Your Home page treats an area under about 10 square feet, roughly a 3 ft by 3 ft patch, as a job most people can handle, and points to EPA’s commercial guide above that. chapter 3 of EPA's mold remediation guide also notes that some biocides are considered pesticides and some states require registered pesticide applicators to apply them in schools, which matters for contractors pricing a disinfection step.

If a kill step is wanted on a hard surface, compare the label dwell times on our hydrogen peroxide page and our Lysol page. Vinegar, which beat 70% ethanol against one of two molds according to the 2015 test, is covered on our does vinegar kill mold page. More on removal is on the mold hub.

Out of scope: this page covers chemistry, contact time and surfaces. For mold and health questions, start with EPA’s Brief Guide or CDC.

Questions people actually ask

How long does it take rubbing alcohol to kill mold?

In the closest lab data, 5 minutes. A 2020 study in the International Journal of Food Microbiology reports that 70% ethanol inactivated all Penicillium commune spores after 5 minutes, with survivors at 1 and 2 minutes in some conditions. CDC reports about 20 minutes for the culture phase of some fungi on surfaces. CDC also says alcohols evaporate rapidly, so a single wipe is unlikely to stay wet that long.

Is alcohol or vinegar better to kill mold?

In the one head to head test found, vinegar did slightly better. Rogawansamy and colleagues, 2015, report that vinegar at 4.0% to 4.2% acetic acid inhibited Penicillium chrysogenum but not Aspergillus fumigatus, while 70% ethanol inhibited neither. Neither is EPA’s first choice: EPA says to scrub hard surfaces with detergent and water and dry them, because dead mold must still be removed.

Does 91% isopropyl alcohol kill black mold?

Not better than 70%. According to CDC, the optimum is 60% to 90% in water, and 91% sits just above that range with only about 9% water. No study found for this page tested isopropyl on dark indoor molds; the closest data are 70% ethanol on Aspergillus and Penicillium. EPA’s method for any color on hard surfaces is detergent, water and drying. How dark molds differ is on our black mold versus regular mold page.

What kills black mold permanently?

No product does on its own; moisture control does. EPA says that if wet materials are dried within 24 to 48 hours after a leak, mold will not grow in most cases, and that porous items such as ceiling tiles and carpet may have to be thrown away. Fix the leak, remove the growth, and keep the area dry.

Does rubbing alcohol kill mold in carpet?

It cannot reach mold in the backing or pad. UF/IFAS Extension says mildewed rugs and carpets should be shampooed and dried as quickly as possible, and that if moisture comes from the floor or padding, the carpet should be removed and the cause corrected. EPA lists carpet with ceiling tiles as porous material that may have to be thrown away.

Sources

  1. CDC's disinfection and sterilization guideline, Centers for Disease Control and Prevention, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008), Chemical Disinfectants: Alcohol. Retrieved 12 November 2026.
  2. Rogawansamy and colleagues, 2015, An Evaluation of Antifungal Agents for the Treatment of Fungal Contamination in Indoor Air Environments, International Journal of Environmental Research and Public Health 12(6): 6319, via PubMed Central. Retrieved 12 November 2026.
  3. Visconti and colleagues, 2020, Impact of intraspecific variability and physiological state on Penicillium commune inactivation by 70% ethanol, International Journal of Food Microbiology 332: 108782, abstract via FAO AGRIS. Retrieved 12 November 2026.
  4. NIOSH Pocket Guide entry for isopropyl alcohol, National Institute for Occupational Safety and Health, CAS 67-63-0. Retrieved 12 November 2026.
  5. Greenfield Global's 70% isopropyl SDS, Greenfield Global USA Inc., Isopropyl Alcohol 70%, revision 28 June 2024, distributor copy. Retrieved 12 November 2026.
  6. an EDM3 70% isopropyl SDS, EDM 3, LLC, Isopropyl Alcohol 70%, issue date 21 May 2024, Delta College facilities copy. Retrieved 12 November 2026.
  7. UF/IFAS Extension's mildew removal sheet, University of Florida IFAS Extension, Jefferson County. Retrieved 12 November 2026.
  8. UGA Extension's mold and mildew stain chart, University of Georgia Cooperative Extension, Textiles: Remove Stains From Mildew, Mold. Retrieved 12 November 2026.
  9. Alabama Cooperative Extension, Salvaging Furniture, Alabama Cooperative Extension System. Retrieved 12 November 2026.
  10. ACRYLITE's cleaning instructions, ACRYLITE (Roehm America), Clean, Disinfect and Maintain ACRYLITE acrylic sheet. Retrieved 12 November 2026.
  11. EPA's Mold Cleanup in Your Home page, United States Environmental Protection Agency, last updated 4 June 2026. Retrieved 12 November 2026.
  12. EPA's Brief Guide to mold, EPA, last updated 18 February 2026. Retrieved 12 November 2026.
  13. EPA's biocide page, Should I use bleach to clean up mold?, EPA, last updated 8 September 2026. Retrieved 12 November 2026.
  14. chapter 3 of EPA's mold remediation guide, Mold Remediation in Schools and Commercial Buildings, EPA, last updated 29 April 2026. Retrieved 12 November 2026.
  15. 40 CFR 152.15, Pesticide products required to be registered, via Cornell Legal Information Institute. Retrieved 12 November 2026.
  16. Dilution figures are nominal arithmetic on label strengths, computed when this page was built. No figure on this page was estimated or invented. Our methodology sets out the standing rules.

Follow the label and SDS of the product in hand, and spot test any finish before treating a whole surface.