What Moisture Reading Is Too High for Drywall? 7 Meter Scales

Illustration: a pin moisture meter resting below a water stained drywall wall

The short answer

What moisture reading is too high for drywall depends on the scale: on a true gypsum scale anything over 1% is wet according to Delmhorst (Tramex turns red at 0.8%), while on a wood equivalent scale such as Protimeter’s %WME, 17 is at risk and 20 or more is wet. Always compare against dry, unaffected drywall in the same house.

Which number counts as too high on your meter? A crosswalk of 7 drywall scales

The first thing to read is not the number but the little label next to it. Five makers print five different drywall conventions, and the Delmhorst BD-2100 owner's manual alone carries three scales (wood, a 0 to 100 reference, and gypsum). The table puts every published dry, middle and wet band for drywall side by side, with the maker’s wording.

Meter and mode What the number is Dry band Middle band Wet band Maker’s note
Delmhorst BD-2100, gypsum scale #3 Gypsum %MC, pins 0 to 0.5 0.5 to 1 Over 1, scale runs 0.2 to 50 Red means too wet for painting or wallpaper, per the Delmhorst BD-2100 owner's manual.
Tramex MEX5, pin mode Drywall %MC, pins 0 to 0.5 0.6 to 0.7 0.8 to 8.5 Over 0.5% is higher than generally acceptable, according to Tramex drywall readings page.
Tramex MEX5 or ME5, pinless Drywall scale 0 to 100 No band No band No band Comparative only: read a known dry spot first, per Tramex drywall readings page.
Protimeter Surveymaster, pin mode %WME 7 to 16.9 17 to 19.9 20 to 99.9 WME is what wood would read in balance with the wall, per the Protimeter Surveymaster manual.
General Tools MMD4E, building mode Relative %, pins 1.5 to 16.9 17 to 19.9 20 to 33 Blue, green, red LEDs; plus or minus 2% accuracy, per the General Tools MMD4E manual.
Wagner Orion, drywall use Relative 0 to 100 No band No band No band Look for areas that read noticeably higher, per Wagner Meters.
Delmhorst BD-2100, reference #2 0 to 100 reference 0 to 85 85 to 95 Over 95 For plaster, concrete and masonry, qualitative, per the Delmhorst BD-2100 owner's manual.
Bands as printed in each maker’s manual or drywall page, retrieved 11 November 2026. Pinless drywall scales carry no fixed bands.
Drywall meter scale crosswalk gaugeWHERE EACH MAKER DRAWS DRY, AT RISK AND WETBands drawn equal width, not to scale. Numbers are the maker’s printed band edges.A 15 readsA 20 readsDelmhorst BD-2100Gypsum scale #30.20.5150RedRedTramex MEX5, pin modeDrywall %MC00.50.78.5Off scaleOff scaleProtimeter SurveymasterPin mode, %WME716.919.999.9DRYWETGeneral Tools MMD4EBuilding materials mode1.516.919.933Blue LOWRed HIGHDelmhorst BD-21000 to 100 reference scale #208595100GreenGreenDry bandMiddle bandWet band
Band edges from the Delmhorst BD-2100 owner's manual, Tramex drywall readings page, Protimeter Surveymaster manual and General Tools MMD4E manual. The right columns are computed: the band a displayed 15 or 20 falls in on each scale. The Delmhorst reference scale is meant for plaster, concrete and masonry, not gypsum.

Two readings of the same wall can therefore disagree by a factor of 20 and both be right. Accuserve reports that dry drywall reads about 20% on a Delmhorst BD-10 and about 8% on a Protimeter Surveymaster, while GreenBuildingAdvisor logged 0.3% on the BD-2100 gypsum scale over an empty, dry stud bay. Which meter suits a restoration kit is covered on our page about moisture meters for water damage.

Is 15% or 20% moisture in drywall bad? Where each number lands on 5 scales

These are the two numbers people ask about most, and neither has one answer. The lookup below is computed from the printed bands above: it shows which light a displayed 15 or 20 would trigger on each scale.

Meter and scale A displayed 15 A displayed 20
Delmhorst BD-2100, Gypsum scale #3 Red Red
Tramex MEX5, pin mode, Drywall %MC Off the scale (it stops at 8.5) Off the scale (it stops at 8.5)
Protimeter Surveymaster, Pin mode, %WME DRY WET
General Tools MMD4E, Building materials mode Blue LOW Red HIGH
Delmhorst BD-2100, 0 to 100 reference scale #2 Green Green
Computed lookup against the maker bands in the crosswalk table (Delmhorst BD-2100 owner's manual, Tramex drywall readings page, Protimeter Surveymaster manual, General Tools MMD4E manual).

Read it this way. Per the maker bands, a 15 on a Protimeter in %WME mode, or on a General MMD4E in building mode, is inside the dry band; on the Delmhorst gypsum scale it is 15 times the 1% red line in the Delmhorst BD-2100 owner's manual. The Tramex pin drywall scale cannot show 15 at all: according to the Tramex drywall readings page, it stops at 8.5% MC. A 20 is wet on every scale except the Delmhorst 0 to 100 reference, which that maker reserves for plaster, concrete and masonry.

Even one meter maker's drywall guide reports a mix that shows why scale labels matter: it calls under 1% ideal, 5 to 12% safe and 17% the point to start remediation, without saying which scale each figure belongs to. Per the maker manuals, the 1% figure matches gypsum scales and the 5 to 17 figures match wood equivalent scales like the one in the Protimeter Surveymaster manual. Mixed together, according to those manuals, they leave drywall at 1% to 5% neither dry nor wet, which no maker scale says.

Illustration: a pinless moisture sensor near an outside drywall corner
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

Why does dry gypsum read under 1% when wood reads 7 to 16?

Gypsum holds water two ways. Its crystal, calcium sulfate dihydrate, carries chemically combined water of about 21% by weight, per the Walls and Ceilings report on GA-231. That bound water is part of the mineral, not dampness. The free water a meter looks for is a fraction of that, per the gypsum scale in the Delmhorst BD-2100 owner's manual puts its whole green band between 0% and 0.5% and its red line at 1%.

Wood is different: it holds water in its cell walls, and the Protimeter Surveymaster manual uses that behaviour as its yardstick. Its %WME is “the theoretical %mc value that would be attained by a piece of wood in moisture equilibrium with the material” being tested. Per that definition, a WME of 20 says wood in balance with that board would sit at 20%, which the same manual reports as WET; it does not say the gypsum holds 20% water.

How much is 19% real water in gypsum? According to a 2006 column in Walls and Ceilings by a former Gypsum Association chief executive notes that lumber can sit at up to 19% and be called dry, but 19% moisture content by weight in gypsum board is so much water that the board “would no longer resemble a rigid panel”.

Number above which each scale shows its wet bandNUMBER ABOVE WHICH EACH SCALE SHOWS ITS WET BANDTramex MEX50.7Delmhorst BD-21001Protimeter Surveymaster20General MMD4E20
Upper edge of each maker’s middle band, from the Delmhorst BD-2100 owner's manual, Tramex drywall readings page, Protimeter Surveymaster manual and General Tools MMD4E manual. Readings above these numbers light the red or HIGH indicator. The two gypsum scales flag wet drywall at a number about 20 to 28 times smaller than the wood equivalent scales. The Delmhorst 0 to 100 reference scale is left out: it is not for gypsum.

ASTM C1789 is the standard practice for calibrating handheld meters on gypsum panels, and the Gypsum Association’s GA-231 asks that meters be calibrated to it, per the Walls and Ceilings report on GA-231. Tramex drywall readings page ties its pin mode drywall %MC scale to ASTM C1789. A meter in wood mode has no such calibration, and Wagner Meters says plainly that its number on drywall “isn’t a true moisture content for drywall”.

How do you set the dry standard on drywall in your own house?

Restorers do not judge a wet wall against a printed number alone. The fifth edition of the water damage standard, ANSI/IICRC S500 2021 (listed on the IICRC S500 page), works from a dry standard, which Restoration and Remediation magazine quotes S500 defining as “a reasonable approximation of the moisture content or level of a material prior to a water intrusion”. Five steps put that into practice.

  1. Pick a reference wall in the same house that never got wet, with the same type of board and finish. Restoration and Remediation magazine quotes ANSI/IICRC S500 that an acceptable method is to read “similar materials in unaffected areas”.
  2. Set the meter to one scale and leave it there. Accuserve cites ANSI/IICRC S500 2021 to use the same meter on the same materials through the whole job, per Accuserve.
  3. Take several dry readings and note the range. The Delmhorst BD-2100 owner's manual says to test areas known to be dry first, then wet areas, and use the dry readings as the reference point.
  4. Read the wet wall starting just above the baseboard at its lowest point and work along the full length, per Accuserve; probe with pins where the pinless scan reads highest.
  5. Log each spot on a sketch with the date. The wall is done when it reads at or near the dry reference on the same scale, not when it falls under a number borrowed from another meter.

Restoration and Remediation magazine also reports, attributing it to S500, a target of within 10% of what similar materials read before the loss, and notes that a reading which still supports microbial growth is not acceptable whatever the dry standard says. The R&R article does not say whether that 10% figure it reports is absolute or relative, so treat it as a check, not a rule. How long reaching it takes is covered on how long water damage drying takes.

What makes a drywall reading falsely high: corner bead, salts, foil?

Metal is the classic trap. GreenBuildingAdvisor reports a Delmhorst pinless meter reading 8 on drywall over an empty stud bay and 35 near an outside corner, and a Ryobi pinless meter showing 78% at a corner with metal bead less than half an inch behind the compound. Both were the bead, not water.

The Protimeter Surveymaster manual warns that “conductive material such as salts, carbon and metal can give false positive readings” and that its search mode reads up to 3/4 inch beneath the surface, so a pipe, wire or foil backing inside that depth can light the bar. It also notes surface condensation has little effect on search mode, which is why a damp sheen alone rarely explains a high pinless number.

Confirm any surprising pinless number with pins on the gypsum scale, away from screws and corners. The Gypsum Association cautions, per the Walls and Ceilings report on GA-231, that ranking areas by how wet they read “is not necessarily a reliable means of assessing the need for replacement”.

Illustration: a stained, slightly sagging drywall ceiling in an empty room
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

When does a high reading mean dry in place, and when cut it out?

A meter tells you the wall is wet; it does not tell you the wall is ruined. EPA Table 1 for water damage within 24 to 48 hours says wallboard “may be dried in place if there is no obvious swelling and the seams are intact”, and to ventilate the wall cavity where possible. Six checks from EPA, the Gypsum Association and a board maker decide which side of the line a wet wall falls on.

Check Points to keeping the board when Source
Water source Sewage or flood water: replace the board GA-231 via Walls and Ceilings report on GA-231
Time since wetting Dried within about 24 to 48 hours Walls and Ceilings report on GA-231; EPA Table 1
Board condition No obvious swelling and seams intact EPA Table 1
Layers Two layers of board are very difficult to dry between GIB Best Practice Series No 8
Insulation behind Wet insulation holds water against the board GIB Best Practice Series No 8
Core feel Soft under a gentle screwdriver prod: consider replacing GIB Best Practice Series No 8
Dry in place or replace, from published guidance retrieved 11 November 2026.

New Zealand board maker GIB, in its GIB Best Practice Series No 8 from August 2019, says under 48 hours with drying under way greatly improves the odds, and past 60 hours “the ship has sailed”. When the board has to go, the cut height and method are on our page about what a flood cut is. Signs and decisions for soaked panels are on the page for wet drywall.

Does ceiling drywall have its own too high number?

No. According to the Delmhorst BD-2100 owner's manual, the Protimeter Surveymaster manual, the General Tools MMD4E manual and the Tramex drywall readings page, each maker prints one set of bands for gypsum whether it hangs on a wall or a ceiling, so a ceiling at 1.2% on the Delmhorst gypsum scale is red for the same reason a wall is. What changes is the evidence around the number: EPA’s dry in place test turns on swelling and intact seams, per EPA Table 1, and those checks apply to ceiling board the same way they apply to a wall.

Ceilings also hide what is above them. GIB’s guidance in the GIB Best Practice Series No 8 flags wet insulation and double layers as reasons board rarely dries, and both are common over a ceiling. Read the ceiling from below and, where the attic or floor above is open, check the insulation and joists too. Where the water came from a roof, the roof side belongs to our sister site, theroofingbrief.com. Readings inside framed walls are covered on water damage in walls.

More on the drying job itself is in our guide to structural drying, and the rest of our water damage coverage sits in the water hub.

Questions people actually ask

What is a normal moisture reading for drywall in a house?

On a gypsum scale, the dry green band in the Delmhorst BD-2100 owner's manual is 0% to 0.5%, per the manual; one published test logged 0.3% over an empty stud bay, per GreenBuildingAdvisor. On a Protimeter in %WME mode the dry band is 7 to 16.9 per the Protimeter Surveymaster manual, and Accuserve reports about 8 on dry drywall with that meter.

Is 70% humidity too high for a house?

Yes for a house drying out. EPA advises keeping indoor relative humidity below 60% and ideally 30 to 50%. For reference, Restoration and Remediation magazine reports about 9.2% WME as the equilibrium for softwood framing at 70 F and 50% relative humidity, which is why the dry reference should be read in the same house on the same day.

Can I paint drywall that reads 0.8% on a gypsum scale?

According to the Delmhorst BD-2100 owner's manual, 0.5% to 1% is its yellow, borderline band and anything over 1% is too wet for painting or wallpaper. At 0.8% the Tramex pin scale already shows red, per the Tramex drywall readings page. Waiting for the wall to match an unaffected wall on the same meter is the safer test before primer goes on.

Do pinless meters show percent moisture on drywall?

Usually not. Tramex drywall readings page describes its pinless drywall scale as comparative readings on a 0 to 100 scale, and the Wagner Orion drywall reading is relative 0 to 100 too, per Wagner Meters. Use those numbers to find the wet area, then confirm with pins on a gypsum %MC scale.

Why does my cheap meter show dashes on dry drywall?

Some building material scales start above where dry gypsum sits. According to the General Tools MMD4E manual, its building materials range is 1.5% to 33% and it shows dashes below 1.5%, with accuracy of plus or minus 2%. Per the Delmhorst manual, that spread is wider than the whole 0% to 1% band its gypsum scale uses to separate dry from wet.

Sources

  1. Delmhorst BD-2100 owner's manual, Delmhorst Instrument Co.: gypsum scale #3 (0.2% to 50%), reference scale #2, LED bands and set points. Retrieved 11 November 2026.
  2. Protimeter Surveymaster manual, GE Measurement and Control, INS5365 Rev. A, June 2013: %WME definition, DRY, AT RISK and WET bands. Retrieved 11 November 2026.
  3. Tramex drywall readings page, Tramex Ltd: MEX5 drywall %MC bands, 8.5% ceiling, ASTM C1789, pinless 0 to 100 drywall scale; undated. Retrieved 11 November 2026.
  4. General Tools MMD4E manual, General Tools and Instruments: MMD4E building materials reference table and specifications. Retrieved 11 November 2026.
  5. Wagner Meters, Wagner Meters, Tony Morgan, updated 26 October 2026. Retrieved 11 November 2026.
  6. one meter maker's drywall guide, moisture meter maker blog, 17 December 2025. Retrieved 11 November 2026.
  7. Accuserve, Accuserve, 14 July 2026: dry drywall readings by meter and the S500 same meter rule. Retrieved 11 November 2026.
  8. Restoration and Remediation magazine, “What Is Acceptable Dry?”, Josh Woolen, June 2021: S500 dry standard and drying goal definitions. Retrieved 11 November 2026.
  9. IICRC S500 page, Institute of Inspection, Cleaning and Restoration Certification: ANSI/IICRC S500 fifth edition, 2021. Retrieved 11 November 2026.
  10. GreenBuildingAdvisor, Peter Yost, 26 July 2018: readings on drywall by meter. Retrieved 11 November 2026.
  11. Walls and Ceilings report on GA-231, Walls and Ceilings, 16 June 2015: Gypsum Association GA-231 and GA-225 recommendations. Retrieved 11 November 2026.
  12. Walls and Ceilings, Walls and Ceilings, Michael Gardner, 1 March 2006. Retrieved 11 November 2026.
  13. EPA Table 1 and EPA, US Environmental Protection Agency, Mold Remediation in Schools and Commercial Buildings, chapters 4 and 2. Retrieved 11 November 2026.
  14. GIB Best Practice Series No 8, GIB (Winstone Wallboards, New Zealand), August 2019. Retrieved 11 November 2026.
  15. The 15 and 20 lookup and the wet line chart are computed from the printed maker bands above when this page was built. No threshold on this page was estimated. Our methodology sets out the standing rules.

Meter bands are maker guidance, not a pass or fail standard. Ask a restorer which meter and scale they used, where their dry reference came from, and to show the logged readings before a wall is closed or painted.