How to Clean Up Blood: Steps by Surface, Bleach Ratio, Wet Time

Illustration: nitrile gloves, folded paper towels and a bucket on a clean vinyl floor, the basic blood cleanup kit

The short answer

How to clean up blood, in order: put on disposable gloves, soak up the blood with paper towels and bag them, wash the surface with detergent, then wet it with an EPA List S disinfectant or household bleach diluted 1:100 (1:10 for big spills) and leave it wet for the label contact time, often 10 minutes. Carpet, mattresses and concrete need different steps.

A few drops, a puddle, or soaked through: which job is this?

Size decides the method before any product does. The CDC environmental infection control guideline splits spills into small ones, which can be cleaned and then disinfected, and spills containing large amounts of blood, where visible organic matter is removed with absorbent material first. Laboratory spills get a stricter method: flood the area with disinfectant before cleaning, using bleach at 1:10.

The University of Wisconsin blood spill SOP (OH-SOP-001, approved 15 December 2010) sends anything beyond a few drops to a trained lead with a spill kit, and treats a carpet spot smaller than a quarter as small.

A third size exists at home: blood that has soaked through a porous item, a mattress, carpet pad or subfloor. No product fixes that, because 531 of the 544 entries on EPA List S are labelled for hard nonporous surfaces only. That is where cleaning turns into removal.

The five steps on a hard floor or counter, in CDC order

Five step blood cleanup sequence on a hard surfaceHARD SURFACE BLOOD CLEANUP, IN ORDER1 ProtectNitrile gloveseyes if splash2 AbsorbPaper towelsthen bag them3 CleanDetergent washlift residue4 DisinfectList S labelor bleach 1:1005 Wait, bagWet for labeltime, then dryLarge spill: CDC lab method floods disinfectant over the towels before step 3, then repeats step 4.
The order CDC and OSHA set for a blood spill on a nonporous surface: absorb, clean, then disinfect for the full wet contact time. Sources: CDC Environmental Infection Control guideline, section E.3; 29 CFR 1910.1030(d)(4)(ii); University of Wisconsin SOP OH-SOP-001.

1. Gloves first, eye cover if it can splash

The University of Wisconsin blood spill SOP makes gloves mandatory for every blood cleanup, and adds eye protection, a mask or face shield and disposable coveralls only when splashing may occur. Check gloves for tears before putting them on. If broken glass is in the blood, 29 CFR 1910.1030 paragraph (d)(4)(ii)(D) says contaminated glass is not picked up with the hands: use a brush and dustpan, tongs or forceps.

2. Absorb and bag, do not mop

Lay paper towels or an absorbent pad over the blood. The Alberta Health Services spill sheet says to blot with paper towels or disposable cloths and that mops are not recommended, because they are hard to clean and can generate aerosols. Bag the soaked towels in a sturdy, leak-proof plastic bag as you go.

3. Clean before you disinfect

Several published spill sheets skip this step. According to the CDC environmental infection control guideline, a study in which even 1:10 bleach failed to fully inactivate high virus levels in large quantities of blood, and notes that EPA label claims are based on use on a pre-cleaned surface. Wash the area with detergent and water and wipe it until no visible residue remains.

Detergent alone is not the finish line. OSHA's 9 March 2010 letter says soap and water may be appropriate for general cleaning but not for decontamination of blood.

4. Disinfect: List S product or diluted bleach

Use an EPA registered product with bloodborne pathogen claims, or household bleach; the next section compares them.

5. Keep it wet for the contact time, then bag and wash hands

The University of Wisconsin blood spill SOP lets disinfectant sit 10 minutes, removes the towels, repeats until no soil remains, then reapplies and leaves it another 10 minutes before wiping dry. Take gloves off inside out into the bag, close it, and wash hands with soap and running water for 30 seconds, as that SOP specifies.

Illustration: an absorbent pad resting on a damp patch of synthetic carpet during spot cleaning
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

Bleach 1:10 or 1:100, or a List S product: which, and for how long?

OSHA's 9 March 2010 letter names two acceptable choices: EPA registered tuberculocidal disinfectants, and 5.25% sodium hypochlorite (household bleach) diluted between 1:10 and 1:100 with water. OSHA's 28 February 1997 letter added EPA registered products labelled effective against HIV and HBV, with effectiveness governed by strict adherence to the label.

According to the CDC environmental infection control guideline, 1:10 gives 5,000 to 6,150 ppm free chlorine and 1:100 gives 500 to 615 ppm. Use 1:100 on a nonporous surface after the organic matter is gone; use 1:10 where the spill is large or is flooded before cleaning. A 1:10 mix is 1 part bleach to 9 parts water, the ratio the Alberta Health Services spill sheet prints.

Bleach strength on the label 1:10 mix, ppm 1:100 mix, ppm
5.25% (strength in OSHA letters) 5,250 525
6.15% (top of CDC range) 6,150 615
Labelled calculation: ppm equals label percent times 10,000, divided by the dilution factor (10 or 100). Values match the ranges in the CDC guideline, section E.3.

Two cautions. The CDC environmental infection control guideline says many grocery store bleaches are not EPA registered as surface disinfectants, which EPA calls an unregistered use. And the University of Wisconsin blood spill SOP says diluted bleach cannot be premixed: mix it at the time of use.

What the List S table says about contact time

EPA's disinfectant list index retired Lists C, D, E and F (the lists most guides still name) and folded them into EPA List S, updated 3 June 2026. Of its 374 entries labelled for residential use, 264 give a hepatitis B contact time. 106 of those need 6 to 10 minutes of wet contact; only 80 work in 1 minute or less.

List S residential HBV contact times, entriesLIST S RESIDENTIAL HBV CONTACT TIMES, ENTRIES1 minute or less802 to 5 minutes776 to 10 minutes106Over 10 minutes1
264 EPA List S entries with a residential use site and a numeric hepatitis B contact time, grouped by minutes the surface must stay wet. Tallied from the EPA table updated 3 June 2026, retrieved 21 November 2026.

Chemistry predicts the wait. Among residential single-ingredient entries on EPA List S, hydrogen peroxide products have a median hepatitis B time of 1 minute, sodium hypochlorite 5 minutes and quaternary ammonium 10 minutes.

Median HBV wet time by chemistry, minutesMEDIAN HBV WET TIME BY CHEMISTRY, MINUTESHydrogen peroxide1Sodium hypochlorite5Quaternary ammonium10
Median hepatitis B contact time for residential EPA List S entries with one active ingredient: hydrogen peroxide (24 entries), sodium hypochlorite (37) and quaternary ammonium (137). Tallied from the EPA table updated 3 June 2026.

Read the claim, not the brand. Of 46 residential bleach entries on EPA List S, 9 list HIV only, with no hepatitis B time. EPA says to search the EPA Reg. No. on your label exactly as printed and follow the contact time for the specific pathogen. OSHA's 28 February 1997 letter quotes one label that needs 30 seconds for HIV-1 and 10 minutes for HBV on the same surface.

Surface by surface: step order, product, wet time and what to throw out

Each row comes from the CDC environmental infection control guideline, the University of Wisconsin blood spill SOP, the Alberta Health Services spill sheet, University of Georgia Extension or EPA List S, named in the last column.

Surface Step order Product class Wet contact time Discard rule Source
Sealed floor, tile, vinyl, counter Absorb, clean, disinfect, wet time, wipe List S hard nonporous label, or bleach 1:100 Label time; SOP uses 10 min twice Towels and gloves bagged CDC E.3; Wisconsin SOP 6.2
Carpet, spot smaller than a quarter Soak with disinfectant, dry, blot, shampoo Carpet safe disinfectant; no bleach 30 min up to overnight Towels bagged Wisconsin SOP 6.7; AHS B
Carpet, larger spill Drip disinfectant, wait, wet/dry vacuum, repeat Carpet safe disinfectant 10 min, longer if heavily soiled Heavy spill: replace carpet and underlay Wisconsin SOP 6.6; AHS B
Mattress, upholstery Blot cool water, wet spotter, flush cool No List S label for soft porous items None labelled Soaked through: remove and discard UGA; EPA List S
Concrete, cement, grout Blot, flood with bleach, wait, blot 1 part 5.25% bleach to 9 parts water 10 min minimum Towels in leak-proof bag AHS A
Clothing, sheets Cold rinse, detergent, cool soak, enzyme presoak Laundry detergent; 3% peroxide spot Soak 30 min; peroxide 1 to 3 min Keep out of the dryer until clean UGA apparel
Broken glass in blood Brush and dustpan or tongs, never hands Then treat the floor as row one As row one Rigid container for sharps 29 CFR 1910.1030(d)(4)(ii)(D)
Surface table compiled from the cited agency, university and extension procedures, read 21 November 2026. Product labels override any time shown here.

Why did OSHA say carpet cannot be decontaminated?

OSHA's 6 May 1994 letter, written about plush carpet, says OSHA has no evidence that decontamination of carpet is possible and that carpeted surfaces cannot be decontaminated, while still expecting employers to make a reasonable effort to clean and sanitize it with carpet detergent products. The CDC environmental infection control guideline repeats that position and suggests carpet tiles in high-risk areas, because a tile can be removed and replaced.

So the carpet steps aim at clean and sanitized. Per the University of Wisconsin blood spill SOP, you soak a small spot with disinfectant, let it dry at least 30 minutes up to overnight, blot, then shampoo or use 3% hydrogen peroxide for discoloration. For bigger spills the SOP drips disinfectant from an unwrung mop without touching the spill, waits 10 minutes, and lifts it with a wet/dry vacuum lined with two plastic bags.

Skip chlorine bleach on most carpet: the Alberta Health Services spill sheet warns it can discolor, recommends a low-level disinfectant instead, and says a heavy spill may mean replacing the affected carpet and underlay. University of Georgia Extension blots synthetic carpet with 1 teaspoon of mild, non-alkali detergent in half a pint of cool water.

Illustration: a cotton sheet soaking in cold water, the first step for blood on fabric
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

Blood on a mattress or couch: what cleaning can and cannot do

University of Georgia Extension treats upholstery with cool water only: blot a fresh stain with cold water, then use a wet spotter of glycerin, white dishwashing detergent and cold water, and flush with cool water. It warns that overwetting leaves a ring.

That removes a surface stain. It does not disinfect the foam underneath: every entry on EPA List S is labelled for hard nonporous surfaces, laundry, or both, and none for mattresses, cushions or upholstery foam. When blood has soaked through the cover, the realistic choice is removal, the same reasoning the Alberta Health Services spill sheet applies to heavily soiled carpet and underlay.

Blood on concrete or grout: flood, wait 10 minutes, blot

According to the Alberta Health Services spill sheet, cement gets its own procedure: blot excess fluid with paper towels, flood the area generously with 1 part 5.25% household bleach to 9 parts water, leave it at least 10 minutes, then blot it up with fresh towels. That flood first order matches the CDC laboratory method for large spills.

Because EPA List S products are labelled for hard nonporous surfaces, unsealed concrete and cement grout sit outside most labels; bleach at the 1:10 strength in that sheet is the documented route. Bleach is corrosive and can corrode some surfaces unless rinsed off, per the Alberta Health Services spill sheet, so rinse with water after the contact time.

Blood on clothes and sheets: cold water before anything else

University of Georgia Extension says to treat blood immediately because stains set by heat are difficult to remove. Rinse fresh blood under cold running water and rub with bar soap or liquid detergent. Per the extension page, soak older stains in cool water for at least 30 minutes; if the stain remains, soak in lukewarm water with an enzyme presoak, rub in detergent, and apply a few drops of 3% hydrogen peroxide for 1 to 3 minutes before rinsing and laundering.

Check the item before it goes in the dryer; dryer heat is the same heat University of Georgia Extension warns sets the stain. For sheets from a large spill, 29 CFR 1910.1030 paragraph (d)(4)(iv) gives the workplace rule worth copying: handle soiled laundry as little as possible with minimal agitation, and bag it where it was used rather than sorting or rinsing it there.

Do the bloody towels go in the household trash?

In most homes, yes, but the answer is set by your state. EPA's medical waste page says medical waste is regulated mainly by state environmental and health departments, and that federal medical waste tracking regulations expired on 21 June 1991.

  • California: California Health and Safety Code 117700(e) excludes household waste from medical waste, and (d) excludes articles containing nonfluid blood.
  • Minnesota: Minnesota Statutes 116.77 excludes infectious waste generated by households from the state’s infectious waste law.
  • Florida: Florida rule 64E-16.002 defines a home user, an individual generating biomedical waste through self-care or care by a family member, and its definition contains no household exemption, so ask the Florida Department of Health how home users should package it.

The Alberta Health Services spill sheet procedure for cement ends the same way: used towels go in a sturdy, leak-proof bag into regular trash. Needles and lancets are a separate stream with their own state rules. The state by state table, including bag specs and haulers, is on our biohazard waste disposal page.

At work, the rules change: 29 CFR 1910.1030 treats liquid blood and items that would release blood if compressed as regulated waste. The rung by rung answer is on our is blood a biohazard page.

When does a blood cleanup become a trauma scene job?

California defines it precisely. The California Department of Public Health describes a trauma scene waste management practitioner as a person who removes human blood, body fluids and other residues from the scene of a serious injury, illness or death as a commercial activity, who must register with the department under Health and Safety Code Chapter 9.5, starting at section 118321, and show a contract with a registered medical waste transporter or facility.

Three signs from the sources above point to that kind of job: blood soaked through carpet pad, a mattress or subfloor (no EPA List S label covers it), a spill large enough that the CDC environmental infection control guideline flood method applies, and any unattended death, where fluids and odor travel into the structure. What a crew removes and why is on our crime scene cleanup page. Odor after an unattended death is covered in decomposition smell removal.

Ask a company three things: its state registration (California publishes a list), the EPA Reg. No. it uses on porous materials, and who hauls the waste. The trade is described on our biohazard cleanup page, and rule explainers sit in the standards hub.

Out of scope: this page covers cleaning, not health effects. If blood reached your eyes, mouth or broken skin, call a doctor; the CDC NIOSH bloodborne diseases page explains the exposure risk.

Questions people actually ask

What do hospitals use to clean up blood?

The CDC environmental infection control guideline tells patient care areas to clean small spills, then disinfect with an intermediate-level germicide or an EPA registered germicide. Household bleach at 1:100, 500 to 615 ppm, is appropriate on nonporous surfaces once the organic matter is removed. Laboratories flood large spills with 1:10 bleach before cleaning, then disinfect again.

Is it better to clean up blood with cloth or paper towels?

Paper towels. The University of Wisconsin blood spill SOP stocks high-absorbent paper towels and absorbent pads in its spill kit, and the Alberta Health Services spill sheet says to blot with paper towels or disposable cloths because mops are hard to clean and may create aerosols. Disposable towels go straight into the bag, so nothing bloody needs laundering later.

Is bleach or hydrogen peroxide better for cleaning up blood?

For disinfecting, either works if the label has the claim. On EPA List S, residential hydrogen peroxide products have a median hepatitis B wet time of 1 minute against 5 minutes for bleach, per the EPA table. A peroxide bottle counts only if its EPA Reg. No. is on that list. According to University of Georgia Extension, 3% peroxide is used for 1 to 3 minutes to lift stains from fabric.

Can you mix diluted bleach ahead of time for a spill kit?

No. The University of Wisconsin blood spill SOP says a 1:10 bleach solution cannot be premixed and must be mixed at the time of disinfection, and suggests small bleach packets sized to the water volume. Keep a measuring cup and an unopened bottle in the kit instead, and check the strength printed on the label before mixing.

Is soap and water enough to clean up blood?

Not on its own. OSHA's 9 March 2010 letter says soap and water may be appropriate for general cleaning but not for decontaminating blood. Detergent is still step three: the CDC guideline says disinfectant claims assume a pre-cleaned surface, so wash first, then apply bleach or a List S product for the full contact time.

Sources

  1. CDC environmental infection control guideline: Environmental Services, section E.3, Cleaning Strategies for Spills of Blood and Body Substances, Centers for Disease Control and Prevention, page last updated 8 January 2024. Retrieved 21 November 2026.
  2. 29 CFR 1910.1030, Bloodborne pathogens, paragraphs (b), (d)(4)(ii) and (d)(4)(iv), via Cornell Legal Information Institute. Retrieved 21 November 2026.
  3. OSHA's 9 March 2010 letter, Appropriate disinfectants for decontamination of blood or OPIM, Occupational Safety and Health Administration. Retrieved 21 November 2026.
  4. OSHA's 6 May 1994 letter, decontamination of plush carpet and hard surfaces, Occupational Safety and Health Administration (archived). Retrieved 21 November 2026.
  5. OSHA's 28 February 1997 letter, EPA registered disinfectants for HIV and HBV, Occupational Safety and Health Administration. Retrieved 21 November 2026.
  6. EPA List S: Registered Antimicrobial Products Effective Against Bloodborne Pathogens, United States Environmental Protection Agency, last updated 3 June 2026; table tallied by us. Retrieved 21 November 2026.
  7. EPA's disinfectant list index, United States Environmental Protection Agency, last updated 24 August 2026. Retrieved 21 November 2026.
  8. University of Wisconsin blood spill SOP: Blood Contaminated Material Clean-up Standard Operating Procedure, OH-SOP-001, University of Wisconsin Madison Environment, Health and Safety, approved 15 December 2010. Retrieved 21 November 2026.
  9. Alberta Health Services spill sheet: Cleaning and Disinfecting: Blood Spills, Feces, Vomit and Other Body Fluids, Alberta Health Services, reviewed September 2019. Retrieved 21 November 2026.
  10. University of Georgia Extension: Remove Stains From Blood, UGA Cooperative Extension Textiles. Retrieved 21 November 2026.
  11. EPA's medical waste page, United States Environmental Protection Agency, last updated 20 April 2026. Retrieved 21 November 2026.
  12. California Health and Safety Code 117700, subdivisions (d) and (e). Retrieved 21 November 2026.
  13. Minnesota Statutes 116.77, Coverage, Minnesota Office of the Revisor of Statutes. Retrieved 21 November 2026.
  14. Florida rule 64E-16.002, Definitions, via Cornell Legal Information Institute. Retrieved 21 November 2026.
  15. California Department of Public Health: Trauma Scene Waste Management Practitioners, Medical Waste Management Program. Retrieved 21 November 2026.
  16. CDC NIOSH bloodborne diseases page, National Institute for Occupational Safety and Health. Retrieved 21 November 2026.
  17. The List S tally, the ppm table and the surface table are our compilations from the sources above; no figure was estimated. Our methodology sets out the standing rules.

Disinfectant labels are the legal instructions for each product: follow the dilution and contact time printed on yours. State waste rules differ; confirm with your state health or environmental department.